Motorcycle valve clearance checks: intervals, symptoms and cost
By Garagely editorial team, Motorcycle maintenanceUpdated 2026-10-18
On this page: Checklist · 16 steps, Before you start, Intervals, Symptoms of tight or loose valves, What the check involves, What drives the cost, By bike type, When to call a mechanic, Log every reading, Frequently asked questions
Your owner's manual sets the valve check interval, in distance, time or hours, and it differs widely between engines. Tight valves are often silent, so hard warm starts, rough idle or lost power can be late signs. Cost follows labor: the bodywork and tank to remove, the number of valves, and whether shims must be ordered.
Checklist · 16 steps
Find the valve clearance interval and procedure for your model in the manual
Why: Intervals are set by distance, time or hours and differ widely between engines.
Identify whether your engine uses shims, screw adjusters or hydraulic lifters
Why: Hydraulic lifters need no routine clearance check; shims and screws decide the job's length.
Find the date, odometer and measured clearances of the last valve check
Why: Past readings show which way each valve is drifting; one reading shows only where it is now.
Let the engine cool to the temperature the manual specifies before measuring
Why: Metal expands with heat, so a clearance measured warm differs from the specification.
Gather feeler gauges, a torque wrench, new gaskets and the manual's special tools
Why: Cover gaskets and seals may need replacing when the cover comes off.
Remove the tank, fairings or airbox parts as the manual directs for access
Why: On many bikes this takes most of the time, and so drives workshop cost.
Turn the engine to each valve's measuring position, with the cam lobe pointing away
Why: A valve can only be measured when it is fully closed, with the lobe off the follower.
Measure every valve with a feeler gauge and write each reading down
Why: A written number per valve is the baseline for the next check.
Compare each reading with the manual's range, intake and exhaust separately
Why: Intake and exhaust valves usually have different specified ranges.
Adjust any valve outside its range, then measure again after locknuts or shims are fitted
Why: Tightening or refitting parts can move the setting, so only the final measurement counts.
Allow for a second visit if shims must be ordered to match your readings
Why: Shim size is worked out from the measured gap, so parts are often ordered after measuring.
Refit the cam cover, plugs and bodywork, tightening each fastener to the manual's torque
Why: Overtightening can damage threads in an aluminum head or cover.
Start the engine and check for oil leaks around the cam cover
Why: A pinched or misseated gasket shows as a weep as soon as the engine warms.
Log the date, odometer or hours and each valve's measured clearance
Why: The notes become the baseline for the next check and show the drift.
Set the valve clearance reminder to the interval your manual gives
Why: Logging the job restarts the countdown, so the next check is not left to memory.
Check four-stroke dirt bike valves at the hour interval your manual lists
Why: Competition four-strokes are often scheduled in engine hours; the manual sets yours.
- Enduro / Dual-Sport
Before you start
Valve clearance is the small gap between the valve stem and the part that pushes it open, which is a cam follower or a rocker depending on the engine. Heat and wear change that gap, so the maker sets a range and tells you to check it.
For the check you need your owner’s manual (it gives the interval, the specification and the procedure), feeler gauges, a torque wrench and the special tools the manual lists. Plan on a cold engine, because the manual specifies the temperature for measuring. Set aside an afternoon, and more if the bike needs the tank or bodywork off.
Intervals
There is no universal interval. Makers set it as a distance, a time limit, engine hours or a combination, and it varies widely between engines. Some manuals list an earlier first check than the later ones, so read the whole chart. Many manuals also carry a shorter schedule for severe use.
Read yours in the owner’s manual. A forum post about a similar bike is not your interval, because engines with the same name can differ by year.
Symptoms of tight or loose valves
Tight valves are often silent. As the gap closes, a valve can stop sealing fully when the engine is hot, so you can lose compression without any sound that warns you. Symptoms can include hard starting when warm, a rough idle, lost power and popping on the overrun. They also have other causes, so they are a reason to look, not a diagnosis.
Loose valves usually announce themselves: a tapping or ticking from the top of the engine that follows engine speed. The tap alone does not tell you the size of the gap.
Clearances do not drift by a fixed amount or in a fixed direction, and on many engines they tend to close over time as the valve and its seat wear. This is why a measured history matters more than any single number.
What the check involves
The job is: access the cam cover, turn the engine to each valve’s measuring position, slide in feeler gauges and compare the result with the manual’s range for intake and exhaust. If a valve is out of range, the fix depends on the adjuster type.
- Screw and locknut: you loosen the locknut, turn the screw until the gauge drags correctly, and tighten the nut while holding the screw.
- Shim under bucket or over bucket: you replace a small shim with one of a different thickness. This usually means measuring, calculating, ordering and refitting, which is why a second visit is common.
- Hydraulic lifters: the engine adjusts itself, and the manual lists no routine clearance check.
What drives the cost
This guide gives no prices, because they depend on your bike, your region and your workshop. The factors are the same everywhere.
Access comes first: how much has to come off (tank, fairings, airbox, radiator hoses) before the cam cover is reachable. Then the number of valves to measure, which grows with cylinders and valves per cylinder. Then the adjuster type: screws can be set on the spot, while shims may require removing the camshafts and ordering parts. Finally, anything bundled in, such as new gaskets, spark plugs or an air filter. Ask a workshop for a quote that spells out whether shims and parts are included.
By bike type
- Street and sport four-strokes: intervals can be long, so the job is rare and the written history matters. Our chain and sprocket guide covers the other drivetrain job to track.
- Enduro and MX four-strokes: intervals are often in engine hours and the engine works hard, so follow the hour schedule in your manual.
- Adventure and dual-sport: distances vary by model and use. Check the manual for severe-use schedules.
- Two-strokes: no poppet valves, so no clearance check (a power valve, if fitted, has its own service in the manual).
- Scooters: many four-stroke scooters have a valve check in the schedule, so read yours.
- Electric: no valves.
- ATVs: four-stroke engines have valve checks, usually listed in distance or engine hours.
When to call a mechanic
If you have never measured valves, a workshop can do the first check while you watch. Shim adjustment, removing camshafts and setting cam timing afterwards are workshop jobs unless you are experienced. Get help too if a reading is far outside its range, if the engine runs rough after the check, or if you find oil leaking from the cam cover. If you want to build your skills first, start with our first DIY service guide.
Log every reading
The value of a valve check is in the comparison. In Garagely, a service log entry takes the date, odometer or hours and notes, so write each valve’s measured clearance in the notes. Next time you open the cover, you will see which valves closed and by how much, and decide with the workshop whether to adjust early. To compare your bike with its maker’s schedule, the model intervals feature loads it for a model linked from the motorcycle catalog.
Valve clearance is one of the reminder tracks, counting by km, hours or months, so logging the job resets the countdown to the next check.
Keep it going in the app
Log the measured clearance for every valve in the notes of a Garagely service-log entry, with date and odometer or hours, so the next check has a baseline.
New to Garagely? Start today
Scan to download
Also available on Google PlayAlso available on App StoreFrequently asked questions
Do I adjust a valve that is still inside its specified range?
The manual's range defines what is acceptable, so a valve inside it is within specification. If a reading sits at the edge of the range and your earlier readings were drifting toward it, ask the workshop what they would do. Your log shows the trend.
What if the previous owner never checked the valves?
Treat the history as unknown and measure now. That first reading becomes your baseline, and you will see at the next check how fast the valves move on your bike.
Should I change the spark plugs and air filter during a valve check?
Access is often the reason to bundle them, because the plugs and airbox parts are already off. Whether they are due is a separate question: compare them with the intervals in your manual.
Can I skip a valve check?
The manual lists the check because the clearance changes with wear, so skipping it means not knowing where the valves stand. If you are unsure whether yours is due, read the schedule in your manual or ask a workshop before deciding.
Sources
- Manufacturer owner's manuals and service manuals - valve clearance specifications, measuring procedure, adjuster type and service intervals
- Athena - Engine valves: issues, adjustment and failure symptoms (parts maker technical article)