The 3-hole oil change: engine, primary and gearbox on a V-twin
By Garagely editorial team, Motorcycle maintenanceUpdated 2026-10-18
On this page: Checklist · 15 steps, Before you start, The three fills, Service intervals, Choosing the oil, Draining and refilling, By bike type, When to call a mechanic, Log all three fills, Frequently asked questions
A 3-hole oil change replaces the three separate lubricant fills on a big V-twin: engine oil, primary chaincase fluid and transmission oil, each through its own drain plug. Each has its own interval and fluid specification in the owner's manual, so follow the manual's figures rather than one number from the internet, and log all three fills.
Checklist · 15 steps
Read the lubrication section of your manual before buying any oil
Why: It names the fluid, capacity, plugs and torque for each fill, and it can differ from forum advice.
Count the drain plugs and fill points your manual lists for the bike
Why: Some V-twins share one sump between engine and gearbox, so the number of fills depends on the design.
Find the engine, primary and transmission lines in the maintenance schedule
Why: Each fill has its own interval, and the figures differ by model and year.
- Cruiser
Note both the distance limit and the months limit for each fill
Why: Many schedules give both, and a bike ridden little still ages its fluids.
Match each fluid to the specification the manual names for that fill
Why: Viscosity and quality class are specs to meet, and the three fills can call for different fluids.
Check the label for the JASO class your manual requires
Why: Oil that shares a chamber with a wet clutch can make the clutch slip if it is the wrong type.
Buy the filter, sealing washers and gaskets your manual calls for
Why: Reusing a crushed washer or a tired gasket is one way to end up with a weeping plug.
Warm the engine briefly, then park the bike upright and level
Why: Warm oil drains more completely, and a level bike keeps the fill amount and level check accurate.
Drain one compartment at a time into its own labelled container
Why: It keeps the three fluids apart so you can compare them and do not mix up the refills.
Tighten every drain and fill plug to the torque in the manual
Why: Plugs often thread into aluminium cases, which strip far more easily than steel.
Replace the engine oil filter in the same visit as the engine oil
Why: A used filter holds oil and contaminants that would go straight into the fresh fill.
Fill each compartment to the capacity stated for that compartment
Why: Too little starves moving parts, and too much can foam or push past seals.
Check each level the way the manual describes, then recheck after running
Why: Oil settles after a run, so the reading before and after can differ.
Look for weeps around every plug and the filter after the first run
Why: A leak is far easier to fix in the garage than at the roadside.
Log all three fills in one service entry with the odometer reading
Why: The primary and gearbox dates are the ones most easily forgotten.
Before you start
Set aside an hour or two for a first attempt and read the lubrication section of your owner’s manual first. It lists which compartments your bike has, the fluid for each, the capacity, the drain and fill points and the torque for every plug.
Have ready a drain pan big enough for the largest fill, a replacement oil filter, new sealing washers or O-rings if the manual calls for them, a torque wrench, funnels and rags. If this is your first time under the bike, your first DIY service covers the basics of tools and safe support.
The three fills
A “3-hole” change is the rider name for changing the three separate lubricant fills on a big V-twin: the engine oil, the primary chaincase fluid and the transmission (gearbox) oil. Each has its own drain plug and its own fill point, hence the name. Changing only the engine oil leaves the other two untouched.
Not every V-twin has this layout. Some designs share one sump between engine and gearbox, and some use a separate oil tank instead of a plug on the case. Your manual’s lubrication diagram shows which layout you own, and that number of fills is the number to service.
Service intervals
Open the maintenance schedule in the manual and find the three lines separately: engine oil and filter, primary chaincase, transmission. Many manuals set an early first service for the new fluids and then a recurring interval. The primary and gearbox figures are often longer than the engine oil figure, but the only numbers that count are the ones printed for your model and year, because they have changed between generations.
Figures quoted online disagree with each other and with factory schedules. Treat a forum number as a prompt to check the manual, never as the answer. If you ride in dust, heat, stop-start traffic or two-up with luggage, look for a severe-use note, since some manuals give shorter intervals for it.
Choosing the oil
The manual names a lubricant for each fill, and the names are not always the same. Some bikes use one fluid for primary and transmission and another for the engine. Read each as a specification to meet: a viscosity grade (SAE J300 defines these), a quality class (API), and, where the oil also lubricates a wet clutch, a JASO motorcycle class such as MA or MA2 when the manual asks for one.
Two questions come up all the time. Can one oil go in all three? Only when your manual lists the same fluid for them; if it does not, do not assume. How much goes in the primary? Each compartment has its own capacity in the manual, and the manual also states how to check the level: the bike’s position, whether the engine should be warm, and where the check point is.
Draining and refilling
Work with the bike upright and level, supported the way the manual allows. Take one compartment at a time so you never lose track of which fluid is which. Remove the plug, let it drain completely, fit a new sealing washer or O-ring if the manual calls for one, and tighten the plug to the manual’s torque. Many plugs thread into aluminium and strip easily, so a torque wrench is the right tool here, not a guess.
On the engine, change the filter at the same time, following the manual’s filter and gasket steps. Fill each compartment with the stated amount, then check the levels at the points the manual names. Start the engine, let it run briefly, look for weeps at every plug and at the filter, then shut it off and recheck the levels once the oil has settled.
Take used fluid in sealed containers to a recycling point; disposal rules vary by country.
By bike type
- Big V-twin cruiser and tourer: this is the layout the term describes, with engine, primary and transmission each on their own plug. Your schedule should list them as separate lines.
- Smaller V-twins: some share lubricant between engine and gearbox, so the schedule has fewer lines and the job has fewer holes. Count what your manual lists, not what a forum thread says.
- Belt final drive: the belt does not change the oil count, but it adds its own inspection, covered in motorcycle belt drive maintenance.
- Shaft drive: the final-drive housing usually has its own oil and plug, a further fill that your manual lists with its own interval.
When to call a mechanic
Hand the job over if you are unsure which plug belongs to which fluid, if any thread feels damaged, or if you do not have a torque wrench. Call one too if a leak persists after you have rechecked the plugs, if the clutch slips or the gears change differently after the service, or if a warning light appears.
Keep the receipt: a dated workshop record helps with warranty and resale.
Log all three fills
The oil reminder in Garagely covers the engine oil, so set it to the engine-oil interval from your manual and let reminders count down in kilometers, hours or months. For the primary and gearbox, use the service log and record all three fills in the same entry: the odometer reading, the parts touched (plugs, washers, filter, gaskets) and what the job cost, whether you did it yourself or paid a shop.
Next time you open the log, the date and reading of the last primary and gearbox fills are right there, which is the part riders usually forget.
Keep it going in the app
Log every 3-hole change as one service entry in Garagely, with the odometer reading, parts touched and cost, so the primary and gearbox dates are never lost.
New to Garagely? Start today
Scan to download
Also available on Google PlayAlso available on App StoreFrequently asked questions
Do I have to change all three at once?
No. They are separate fills with separate lines in the schedule, and doing them in one visit is a convenience, not a rule. If the manual puts the primary due at a different reading than the engine oil, you can change each when it comes due.
What do milky or glittery drained fluids mean?
A milky look suggests water has mixed in, for example from condensation on short trips or a failed seal. Fine metallic glitter or flakes point to wear. Neither can be diagnosed from a photo, so have a mechanic look before you rely on the bike, and note what you saw in the log.
What if a drain plug will not budge or the threads feel soft?
Stop. Do not add leverage or reach for an impact driver. Damaged threads in a case may need a repair insert or a new part, and a mechanic can do that cleanly. Check that the socket fits the plug properly first, because a poor fit rounds the head.
Should I still change the fluids if I hardly ride?
Yes, if your manual sets a time limit. Oil also takes on moisture and fuel from short trips, so it ages on the calendar as well as on the odometer. Follow whichever limit your manual reaches first.
Sources
- Manufacturer owner's manuals - lubrication chapter and maintenance schedule (engine oil, primary chaincase and transmission fluid: type, capacity, interval, torque)
- SAE J300 - engine oil viscosity classification
- JASO T 903 - four-stroke motorcycle engine oil standard (JASO MA, MA2 and MB classes)
- American Petroleum Institute - engine oil quality categories