ATV pre-ride inspection: the T-CLOC checklist explained
By Garagely editorial team, Motorcycle maintenanceUpdated 2026-10-18
On this page: Checklist · 15 steps, Before you start, Tires and wheels, Controls and cables, Lights, oil and fuel, Chain or driveshaft, and chassis, By bike type, When to call a mechanic, Build the habit, Frequently asked questions
T-CLOC is the ATV Safety Institute's pre-ride inspection, named for what it covers: Tires and wheels, Controls and cables, Lights and electrics, Oil and fuel, and Chain/driveshaft and chassis. Walk around the machine in that order before every ride, so a loose, leaking or worn part is found in the yard instead of on the trail.
Checklist · 15 steps
Check each tire's cold pressure with a low-pressure gauge against the manual
Why: ATV tires run at far lower pressures than car tires, and a coarse gauge misreads them.
Look over all four tires for cuts, bulges, embedded objects and bead leaks
Why: A damaged tire at low pressure gives little warning before it goes flat.
Check the wheel nuts are tight and the rims have no cracks or dents
Why: Loose nuts and bent rims show up first as a wobble; the tightening torque is in your manual.
Grip each wheel top and bottom and rock it to feel for play
Why: Play points to a worn wheel bearing or suspension joint that will get worse with load.
Check the throttle moves freely and snaps closed when you release it
Why: A sticking throttle is a safety fault; do not ride until it is fixed.
Squeeze the brake lever and press the pedal, checking firm feel and travel
Why: A spongy lever or long travel suggests air in the system, a fluid problem or worn pads.
Check levers, cables and the steering for free, full movement lock to lock
Why: Frayed cables and stiff or loose steering fail without warning once you are moving.
Test the headlight, brake light and kill switch before you pull away
Why: Lights make you visible, and the kill switch is how you stop the engine in a hurry.
Check the engine oil level on level ground, as the manual describes
Why: Low oil damages an engine fast, and the manual says how to read the level on your model.
Check the fuel level and look under the machine for fuel or oil drips
Why: A fresh drip or fuel smell is easier to deal with in the yard than after heat and vibration.
Check differential and drive fluid levels where the manual lists them
Why: Low or milky fluid points to a leak or water ingress that you want to know about before a ride.
Look over the frame, suspension arms and axle bolts for cracks or looseness
Why: A crack or loose bolt on a suspension part gets worse with each bump.
Check the CV boots, drive shaft or chain and sprockets for damage and slack
Why: A torn boot or a loose chain wears the drivetrain quickly; slack is set in the manual.
Start the engine and check idle, brake hold and gear selection before leaving
Why: A short stationary test finds a fault where it costs you nothing.
Log any fault you fix or defer so it is tracked, not forgotten
Why: A written note keeps a small deferred item from turning into a forgotten fault.
Before you start
The name T-CLOC lists what to check, in order: Tires and wheels, Controls and cables, Lights and electrics, Oil and fuel, and Chain/driveshaft and chassis. The inspection comes from the ATV Safety Institute; check its site for the current version. This page explains the reason behind each step and adds the details your owner’s manual supplies, since pressures, fluid types and torques differ by model.
Have the owner’s manual, a gauge that reads low pressures, a flashlight and a rag to hand. Put the machine on level ground with the engine off and cold. The check covers the machine only. Helmet and riding gear are a separate habit.
Tires and wheels
ATV tires run at low pressure, far below what a car tire carries, so a normal tire gauge may be too coarse to read them well. Use a low-pressure gauge, check the tires cold and compare the figure with the one in your manual. Many machines also carry a pressure label on the body. Pressure that differs side to side can make the machine pull or lean, so keep the pairs matched.
Then look at each tire for cuts, bulges and objects stuck in the tread, and listen for a hiss at the bead. Check that the wheel nuts are tight, with the torque from the manual, and that rims are not cracked or dented. Finally grip each wheel at the top and bottom and rock it: free play there means a bearing or a suspension joint.
Controls and cables
Squeeze the brake lever and press the foot pedal. Both should feel firm, with the travel the manual describes, and the machine should not creep forward with the brake held. A soft lever is not a quirk you adapt to.
Work the throttle: it must move freely and snap shut when released, with the bars turned fully left and right. Check the clutch or shift lever, the cables for fraying and the steering for smooth, full movement lock to lock. If the throttle sticks, stop there. A sticking throttle is a reason not to start the ride.
Lights, oil and fuel
With the key on, test the headlight, tail and brake light, and then the kill switch. The kill switch is the control you use in an emergency, so make sure it actually stops the engine.
Check the engine oil on level ground, using the dipstick or sight glass as the manual describes. Check the fuel level and the lines, then look under the machine for drips and for fuel or oil residue on the skid plate. Where the manual lists differential or final-drive fluid levels, check those too: milky or low fluid points to a leak or to water getting in, which matters more after a wet ride.
Chain or driveshaft, and chassis
Look at the frame tubes, suspension arms and axle bolts for cracks, bends and anything loose. A mounting bolt that has backed out is easy to fix in the yard and hard to fix on a trail. Check the CV boots for tears and grease thrown around the wheel well. On a chain-driven machine check chain tension and the sprockets against the manual. On a shaft-drive machine look for oil weeping at the seals.
Finish with a short stationary test. Start the engine, check the idle, hold the brake and select each gear. If something sounds or feels different from last time, trust that instinct and look closer before you ride.
By bike type
- Utility 4x4: check front and rear differential fluids where listed, and the 4WD engagement as the manual describes. Look at the hitch, racks and winch wiring if they have been used.
- Sport quads: most have a chain, so check tension, sprocket wear and the rear axle bearings. Engine intervals on competition machines are often in hours in the manual.
- Youth models: also check that the throttle limiter is set and works, and that the rider fits the age and size labels on the machine.
- Electric: the oil and fuel steps become battery charge and the charge port. Check connectors for damage and keep to the maker’s washing instructions.
When to call a mechanic
Get help if a brake is soft or drags, a throttle sticks, steering feels loose or notchy, a wheel has play, a frame or suspension part is cracked, or fluid is milky or leaking. Brakes, steering and the frame are safety items, so a qualified mechanic decides, not a checklist.
Build the habit
The check works because it is the same every time. Tie it to something you already do, such as fuelling up or loading the trailer, and keep a record of what you find. After a wet or muddy ride, repeat the oil, fluid and leak checks when you park, because water that got past a seal is easier to spot early. Write down what you saw, however small, so the next check starts from a known state. Garagely’s pre-ride check turns the walk-around into a tap-to-tick list with parts that are due for service shown first. If you are shopping for a machine, the used ATV checklist covers what to inspect before you buy.
Keep it going in the app
Run the pre-ride check in Garagely before each ride and tap items off as you walk around the machine; parts that are due for service are shown first, so they get noticed.
New to Garagely? Start today
Scan to download
Also available on Google PlayAlso available on App StoreFrequently asked questions
Is T-CLOC the same as the motorcycle T-CLOCS checklist?
They are close relatives. The motorcycle version, T-CLOCS, from the Motorcycle Safety Foundation, adds an S for Stands (sidestand and centerstand) because a motorcycle stands on its own stands. An ATV has none, so T-CLOC ends at the C for chain/driveshaft and chassis.
How long does a pre-ride inspection take?
Longer the first few times, while you learn where each item is. Once the order is routine it takes a few minutes, which costs far less than a trailside repair. Never shorten the checks to save time.
Do I repeat the check at lunch or on the second day of a trip?
Yes, at least the quick parts: tire pressure and damage, wheel nuts, leaks, throttle and brakes. Vibration and impacts loosen fasteners during a day of riding, and a stop is the cheapest time to catch it.
Can I ride with a small fault, like a dead brake light?
Fix it first. Lights, brakes, throttle and steering are safety items, and rules about lighting on public land vary by country. Postpone the ride, or trailer the machine, rather than hoping the fault stays small.
Sources
- ATV Safety Institute - T-CLOC pre-ride inspection and rider training
- ATV Safety Institute - T-CLOC inspection checklist (PDF)
- University of Minnesota, UMASH - T-CLOC pre-ride inspection checklist (PDF copy of the ATV Safety Institute checklist)
- Manufacturer owner's manuals - tire pressure, fluid levels, wheel nut torque, chain slack, maintenance chart