Track day bike prep: tech inspection checklist for a street bike
By Garagely editorial team, Motorcycle maintenanceUpdated 2026-10-18
On this page: Checklist · 16 steps, Before you start, Read the tech sheet, Coolant, fluids and fasteners, Brakes and tires, Lights, mirrors and chain, By bike type, When to call a mechanic, Back to road spec, Frequently asked questions
Start from your organizer's tech sheet, then prepare the bike to match it: a coolant the organizer allows, fresh brake fluid and pads with material left, drain plugs and filter secured the way the sheet asks, tires with legal tread and a sound date code, a checked chain, and lights and mirrors taped or removed. Every number comes from your manual or the sheet.
Checklist · 16 steps
Download your organizer's tech inspection sheet and read it before you buy anything
Why: Rules on coolant, tape, tread and safety wire differ by organizer, and the sheet is what inspectors use.
Ask the organizer in writing whether electric bikes are accepted at the event
Why: Rules differ by organizer, and an answer after you have booked and paid is too late.
- Electric
Write down your road settings before changing anything, then log each change
Why: Pressures, sag, coolant and mirrors all have to go back, and a list is more reliable than memory.
Finish any overdue service at least a week before the track day
Why: It leaves time to fix what the service uncovers and to ride the bike and re-check for leaks.
Swap ethylene glycol coolant for one your organizer allows, following your manual's drain steps
Why: Spilled ethylene glycol coolant is slippery on a track surface, so some organizers prohibit it outright.
Bleed in fresh brake fluid of the grade printed on your reservoir cap
Why: Old fluid has absorbed water, which lowers its boiling point under repeated hard braking.
Check pad thickness against your manual's limit and fit new pads if marginal
Why: Pads that are fine for the road can be used up in a few sessions of hard braking.
Safety wire the drain plug, filter and other parts your organizer lists
Why: Wire keeps vibration from backing a part out, and a lost plug puts oil on the track.
Check axle nuts, pinch bolts, caliper bolts and bars against the manual's torque values
Why: Track loads work fasteners loose, and only the manual's figures are right for your bike.
Set oil to the correct level and look for leaks around gaskets and hoses
Why: A leaking bike can be turned away at inspection, and a small weep grows under track loads.
Check tread depth and DOT date code against the organizer's tire rules
Why: The sheet may set a minimum tread, and the last four digits of the DOT code give the tire's age.
Look up your tire maker's track pressure advice and bring a reliable gauge
Why: Track pressures are set differently from road pressures, and the maker's guidance beats guessing.
Clean and lube the chain and set slack to your manual's figure
Why: A loose or dry chain wears quickly and is a safety risk at track speeds.
Check that the throttle snaps closed and that levers and pedals move freely
Why: Inspectors test the controls, and a throttle that sticks open is dangerous at any speed.
Tape or remove lights, mirrors and other glass as your organizer requires
Why: Broken glass and plastic on the track can cause crashes, which is why organizers ask for this.
Pack tape, wire and pliers, a torque wrench, a gauge and a basic tool kit
Why: Paddock fixes happen between sessions, and inspectors can send you back to fix one thing.
Before you start
Get the tech sheet from the organizer’s website or confirmation email and read it first. Every rule below is written as “your organizer decides”, because they do. Allow a few hours of work spread over the week before the event, so you can ride the bike once afterwards and look for leaks. Bring your owner’s manual to the garage: it supplies the coolant spec, brake fluid grade, torque values and chain slack.
Before you change anything, write down your road figures. Open the tire pressure tool in Garagely for a cold road starting point, and note your manual’s pressures, your sag and your suspension clicks. You will want them back after the event.
Read the tech sheet
Tech inspection is a person with a list looking at your bike before the first session. Tech sheets differ, so use the one for your event. For an example of how detailed one can be, AHRMA’s published Tech 101 sheet, written for racing, lists items that must be safety wired, bans ethylene glycol coolant, requires a self-closing throttle and says tires are subject to the inspector’s approval. A track day sheet may be shorter or different, which is why you read yours.
A clean bike helps. The same AHRMA sheet points out that cleaning reveals leaks, cracks and loose parts, and that inspectors are more likely to see a well-prepared machine. Wash it a day or two before, then look for anything that weeps.
Coolant, fluids and fasteners
Many organizers ban ethylene glycol coolant, because spilled glycol is slippery on a track surface. If your organizer does, the usual alternative is water with a wetter additive, or another product your organizer’s sheet names. Drain and flush the system as your manual describes, refill with what the sheet allows, and bleed any air from the system.
If the sheet says nothing, ask. Do not guess, because a fluid the organizer refuses means a failed inspection or a bike that stays in the van.
Check the oil level and look around gaskets, the sump, hoses and the fork seals for weeping. A leaking bike can be turned away at inspection.
Safety wire is a self-check that you tightened the part and a backstop if it loosens. Which parts need it comes from the organizer’s sheet; common candidates are the drain plugs, the oil filter or its cover, the fill cap and the radiator cap. Wire so the pull is in the tightening direction, and ask someone who has done it to check yours the first time. Then go over the axle nuts, pinch bolts, caliper bolts and handlebar clamps with a torque wrench, using the figures in your manual.
Brakes and tires
Brake fluid absorbs water over time, which lowers its boiling point. Use the grade printed on your reservoir cap. DOT 3, DOT 4 and DOT 5.1 are glycol-based, and FMVSS No. 116 sets minimum dry and wet boiling points for each grade; DOT 5 is silicone-based and does not mix with them. Fresh fluid in a sealed bottle gives the widest margin for a day of hard braking.
Look at pad thickness with the caliper in place and compare it with your manual’s limit. A pad that still has material can be gone after a few track sessions, so if it is marginal, replace it now.
For tires, check tread against the organizer’s minimum and read the DOT code: the last four digits are the week and year of manufacture. Look for cuts, cracks and flat spots. Track pressure is set differently from road pressure, and tire makers publish their own guidance. Michelin’s on-track page, for one, says to set pressure at ambient temperature before the first ride, so look up your own tire’s advice and bring a reliable gauge.
Lights, mirrors and chain
Organizers often ask you to tape headlight and taillight lenses or remove mirrors and other glass, so broken pieces do not end up on the track. Use the tape the sheet describes and keep the removed parts in a labelled box. Check that the throttle snaps closed, the levers move freely and the kill switch works.
Clean and lube the chain, then set slack to your manual’s figure. A worn chain and sprockets are cheaper to replace at home than to find out about at speed.
By bike type
- Chain drive: inspect the chain, both sprockets and the chain guide. Safety wire or cotter-pin the axle nut if the sheet asks.
- Belt or shaft drive: ask the organizer whether your bike is welcome, and check the belt or the final-drive oil as the manual describes.
- Electric: ask the organizer before you book whether electric bikes are accepted, and how they handle charging and battery safety. Do not assume.
- Scooters: check with the organizer first. Many events are aimed at sport bikes.
When to call a mechanic
Hand over the brakes if you have not bled a system before, or if the lever is soft or the fluid is dark. A mechanic should also handle bent discs, play in the steering head or wheel bearings, a fork that leaks, a coolant system that will not hold pressure, and any frame damage. Safety wire is easy to do wrong; a shop that races or a rider who has wired before can check it in minutes.
Back to road spec
When the day ends, your list tells you what to undo: coolant, pressures, tape, mirrors, settings. Garagely’s suspension assistant keeps each setup as a saved version, and the free sag calculator gives a starting point without an account. Then follow the after track day checklist before you ride home on the road.
Keep it going in the app
Run the sag wizard in Garagely (Pro) before the event and save your track setup as a version, so you can return to your road settings afterwards without guessing.
New to Garagely? Start today
Scan to download
Also available on Google PlayAlso available on App StoreFrequently asked questions
Do I need different oil for the track?
Your manual's grade and specification are the baseline. Fresh oil before an event is a common choice rather than a universal rule, and checking the level between sessions is cheap insurance on a bike that is working harder than usual.
Do I need track-only tires for my first event?
Your organizer's rules decide. A road-legal sport tire that passes the tread and condition checks is a usual starting point; track-only tires usually call for their own pressure advice and, on some, warmers.
What should I do with ABS and traction control?
Read your manual to see whether you can adjust or switch them off, and ask your organizer whether it has a rule. Make any change in a quiet moment in the paddock, not on the grid.
Should I change my suspension settings for the track?
Start with the figures in your manual, set sag first, and change one thing at a time. Note every click so you can return to your road setup afterwards.
Sources
- Manufacturer owner's manuals - coolant specification, brake fluid grade, torque values, chain slack, tire pressures
- AHRMA, Tech 101: How to breeze through tech inspection (a racing organization's published tech sheet, used here as an example)
- Michelin, motorcycle tyre pressure guide (on-track pressure section)
- 49 CFR 571.116 - FMVSS No. 116, Motor vehicle brake fluids (DOT 3, 4 and 5.1 boiling points)